Mute/Unmute
How do I mute and unmute the microphone?
Touch the mute area on the microphone body to mute the microphone. The dynamic indicator light will turn red to indicate that the microphone is muted. Touch the area again to unmute the microphone and resume recording.
RGB Lighting
How do I turn the RGB lighting on or off?
Press and hold the RGB Lighting button for 3 seconds to turn the lighting effects on or off. Short-press the button to cycle through the available 13 lighting effects.
4-in-1 Control Knob
What functions does the 4-in-1 control knob support?
The 4-in-1 control knob provides convenient access to the following functions:
Microphone Gain
Headphone Monitoring Volume
Monitor Mix
Noise Reduction
Wireless Pairing
How do I switch between the different control functions?
Short-press the 4-in-1 control knob to cycle through the available functions. The corresponding function indicator will illuminate white to show the currently selected mode. Rotate the knob to adjust the selected setting.
Microphone Gain
How do I adjust the microphone gain?
Press the 4-in-1 multi-functional button to switch the indicator light to the mic gain mode (lights up white). It’s recommended to turn down the mic gain first, and then turn it up gradually until the desired loudness.
Rotate the encoder clockwise to increase gain or counterclockwise to decrease it. The number of illuminated segments on the light ring changes accordingly.
The microphone gain onboard control in TK1 is only available in USB and wireless mode. For XLR mode, adjust the gain through your audio interface or compatible software.
Why is my microphone audio too quiet or too loud?
If the audio is too quiet, increase the microphone gain. If it is too loud or distorted, lower the gain. In XLR mode, adjust the gain on your audio interface or through compatible software.
Headphone Monitoring Volume
How do I connect headphones to the microphone?
Fully insert the headphone into the 3.5mm headphone jack on the mic.
The “fifine Microphone” will become the default output device in the system sound settings to output the system’s sound to the headphone jack along with the monitoring sound.
When the mic is on, and the mic gain and headphone volume controls are not turned to zero, you’ll hear your voice.
How do I adjust the headphone monitoring volume?
Press the 4-in-1 multi-functional button to switch the indicator light to the headphone monitor volume control (lights up white). Rotate clockwise to increase the headphone volume; rotate counterclockwise to decrease the headphone volume.
Why can't I hear my own voice through the headphones?
Make sure the headphones are fully plugged into the microphone’s 3.5 mm jack. Check that the microphone is on and that both the mic gain and headphone volume are not set to zero. Also, confirm that the correct audio output device is selected in your system settings.
Monitor Mix
How do I adjust the balance between monitoring audio and computer audio?
Short-press the 4-in-1 control knob to select Monitor Mix mode. The corresponding indicator will illuminate white.
Rotate the knob to adjust the balance between microphone monitoring and computer audio:
Turn fully counterclockwise to hear only your microphone monitoring.
Turn fully clockwise to hear only computer audio.
Set the knob between the two extremes to hear both sources simultaneously.
How do I hear both my microphone and computer audio simultaneously?
Set the monitor mix between the two extremes to hear both microphone monitoring and computer audio. Adjust the balance to your preference.
Noise Reduction
How to adjust the noise reduction level?
The fifine TK1 supports three levels of noise reduction. You can adjust the level directly using the 4-in-1 control knob on the microphone or the noise reduction button on the receiver. No computer software is required.
Adjust with the 4-in-1 knob
Short-press the 4-in-1 control knob until the Noise Reduction indicator illuminates white. Rotate the knob to adjust the noise reduction level. Turn clockwise to increase the level and counterclockwise to decrease it.
Adjust with the receiver
Short press the noise reduction button to switch the TX noise reduction level. Press and hold the RX noise reduction button for 5 seconds to enter re-pairing mode.
Re-enter Pairing Mode For Wireless Pairing
How do I re-enter pairing mode using the 4-in-1 control knob?
Press and hold the 4-in-1 control knob for 5 seconds to enter pairing mode and search for available pairing signals.
The ring of dynamic lights flashes BLUE rapidly, and the TX signal on the receiver will flash green. Then After pressing the Noise Reduction of the receiver for 5 seconds, the microphone will connect again.
