Skip to main content

How to Control the fifine AMX3 Microphone(Onboard Function Guide)?

Written by Lola J. Strain

3-in-1 Control Knob

What can I do with the 3-in-1 control knob?

The knob can control 3 different functions of the microphone. Short-press the knob to switch the control mode among: mic gain control, headphone monitor volume control, and monitor sound and computer audio balance. There will be an indicator light to show the current function status.

Tip: Press and hold the knob for 5 seconds to restore factory settings.

Adjust mic gain with 3-in-1 knob

Press the knob to switch the indicator light to the mic gain mode. Then turn clockwise the knob to increase the selected setting and counterclockwise to decrease it.

It is suggested that you turn down the mic gain first, and then turn it up gradually to get the desired loudness.

Adjust headphone jack and headphone monitor volume with 3-in-1 knob

If you want to monitor your voice in real time, plug your headphones into the 3.5 mm headphone jack on the bottom of the microphone. The "fifine AMX3" will become the default output device in your system sound settings, allowing both computer audio and microphone monitoring audio to be played through the headphone jack.

How to adjust the level:

  • Make sure your headphones are fully inserted into the microphone's headphone jack.

  • When the microphone is on and both the microphone gain and headphone volume are set above zero, you will hear your voice in real time.

  • Press the knob to switch the indicator light to the headphone monitor volume control. Turn the knob left to increase the headphone volume, and turn right to decrease the headphone volume.

Balance the monitor voice and computer audio with 3-in-1 knob

Press the knob to switch the indicator light to the Monitor/Computer Audio balance mode. The dynamic RGB Panel will show the audio rate of monitor voice and computer audio.

  • When you turn the knob to the Left, the volume of the device audio (such as the audio from your PC or PS5) remains unchanged, and the monitor level decreases.

  • When you turn the knob to the right, the monitor level remains unchanged, and the device audio (such as the audio from your PC or PS5) decreases.

Low-Cut & Mid-Boost Filter

Low-Cut Switch

  • Left: Low-cut filter is off.

  • Right: Attenuates frequencies below 100 Hz to reduce wind noise and other low-frequency noise.

Midrange Boost Switch

  • Left: Enables midrange boost to make vocals stand out more clearly.

  • Right: Sets the microphone’s high-frequency response to a flat state.

Mute Control

How do I mute or unmute the microphone?

Touch the mute LED panel to switch between mute and recording modes.

During recording, the level meter lights up dynamically according to your voice level. When the microphone is muted, the dynamic indicator stays solid red. Touch the panel again to unmute the microphone.

RGB Lighting Control

How do I control the RGB lighting effect?

Press and hold for 3 seconds to turn the RGB lighting on or off. Short press to select RGB lighting modes and colors.

There are 6 RGB lighting modes integrated into the microphone: Static Single Color, Rainbow Flowing, Multicolor Gradient, Multicolor Breathing, Ring Flowing, and Sound-Synced Gradient.

Tip: RGB effect memory function: When the RGB light is turned on again, it will stay in the same RGB effect as before it was turned off.

Reset the Microphone to Factory Settings

Press and hold the designated button for 5 seconds until the ambient light flashes green, then release it. Wait for the green light to flash three times. The lighting will return to the Rainbow Flow effect, indicating that the reset is complete.

Are the Microphone's Hardware Controls Available in Both USB and XLR Modes?

  • USB Mode: All built-in microphone controls and software controls are available.

  • XLR Mode: Functions such as mute and knob controls must be adjusted through the connected audio interface or sound card. RGB lighting and software controls are unavailable. However, the physical low-cut and midrange boost switches remain functional.

Did this answer your question?